TAMCO CLEARS

HC-7677 No-Wax Clearcoat

HC-7677 No-Wax Clearcoat offers the ultimate in gloss and DOI with medium to fast dry times. This clear will give a show-car finish without buffing and applies easily, levels fast, and uses a simple 4:1 mix ratio.  This clear is the most durable clear that we make and passes 20 year test for durability!  4000 hour UV testing (max) and is very chemical resistant - including SKYDROL!  Because this product is so durable- it has a small buffable capability!  Do not try to buff after 72 hours! 

Mix Ratio:

Component                                     Volume                          Weight (Cum. Qty)

HC-7677 SuperFast Glamour Clear             4                                       684 grams

HH-76-series (7603,05,07)                        1                                      871 grams

Reduction Not Needed: Reduce UP TO 10% with HR series reducers ONLY!

Viscosity

18-20 seconds in #2 Zahn Cup

Pot Life

6 hours at 70F

Gun Setups:

Conventional

Siphon Feed: 1.5 mm – 1.7 mm (0.059” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.055” – 0.063”)

HVLP

Siphon Feed: 1.6 mm – 1.7 mm (0.063” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.050” – 0.063”)

Air Pressures

Conventional

Siphon Feed: 25-35 psi at the gun

Gravity Feed: 25-35 psi at the gun

HVLP 6-8 psi at the gun

Application:

1. 
   
   Allow basecoat to dry 15-30 minutes – 30 minutes if applying multiple coats of pearl or if shop is below 70F.
2. 
   
   Apply 2 medium-wet coats of HC-7677 with 5-10 minutes flash between coats.
3. 
   
   1. Do not apply more clear after 1 hour from completion.
   2. HC-7677 is a slightly amber clear, that will not be noticeable as a clear
   3. This product "flows" and you will notice "orange-peel" level off by itself. The slower the reducer, the greater the leveling.
   4. Can be buffed for up to 3 days (at 70 degrees) after overnight dry.  After 12 hours, this product is 90-95% cured and can be buffed, striped or delivered.
   5. We do not recommend baking, but can be baked at 140 for 20 minutes and is 95% cured (to buff or deliver) in 3 hours after cooldown
   6. Allow 2 weeks for TOTAL CURE

Flash/Dry Times (Air Dry):

Flash Between Coats: 5-10 minutes

Dust Free: 15 minutes

Time to Assemble 8 hours

Time to Polish 8 hours

Time to Stripe 8 hours

Time to Deliver 8 hours

Time to Decal 8 hours

Flash/Dry Times (Bake @ 140F):

Flash Before Bake 5-10 minutes

Cycle Time 20 minutes at 140F metal temperature

Dust Free At cool down

Time to Assemble At cool down

Time to Polish 180 minutes after cool down

Time to Stripe 60-180 minutes after cool down

Time to Deliver 3 hours after cool down

Polishing:

Optimum Times: Air Dry: 12 hours @ 70F; Bake: 180 minutes after cool

Sanding: Use 1500 grit or finer or use 1500 DA or finer

Compounding: Use finishing compound. Apply a thin ribbon of material to the

area to be polished. Use a double sided wool pad or a foam

pad. Maintain air polisher or variable speed polisher at 1800-

3000 rpm. Remove excess finishing compound with a clean

soft cloth prior to applying finishing polishing.

Safety:

Before using any Tamco products be sure to read all safety warnings and MSDS. Please read all directions carefully.For professional use only by trained painters. Not for sale or use by the general public.

Technical Data & Physical Properties:

Color Clear Sprayable Viscosity 18-20 sec. #2Z

Pot Life 4-8 hour Mix Ratio 4:1

Weight Solids 48% Volume Solids 43%

Gloss Excellent Weight per Gallon 8.10 lbs

Color Holdout Excellent 

Humidity Resistance Excellent Flash Point <25F

Solvent Resistance Excellent Package

VOC 3.25 lbs/galRepairability 

Excellent RTS VOC 3.50 lbs/gal

Florida Exposure Excellent 

Chip Resistance Excellent

HC-7642 SuperFast Glamour Clear

Availablity limited:

HC-7642 SuperFast Glamour Clear is a medium to hi-solids clear that offers the ultimate in gloss and DOI with unprecedented speed. This clear can be polished in as fast as 3 hours air dry and 20 minutes when baked at 120F.

Mix Ratio:

Component                                             Volume               Weight (Cum. Qty)

HC-7642 SuperFast Glamour Clear                     4                        684 grams

HH-7603/7605/7607 Activator                           1                        871 grams

No reduction needed. Can reduce 5-10% with HR series reducers ONLY!

Viscosity

17-19 seconds in #2 Zahn Cup

Pot Life

2 hours at 70F

Gun Setups:

Conventional

Siphon Feed: 1.5 mm – 1.7 mm (0.059” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.055” – 0.063”)

HVLP

Siphon Feed: 1.6 mm – 1.7 mm (0.063” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.050” – 0.063”)

Air Pressures

Conventional

Siphon Feed: 25-35 psi at the gun

Gravity Feed: 25-35 psi at the gun

HVLP 6-8 psi at the gun

Application:

    1.    Allow basecoat to dry 15-30 minutes – 30 minutes if applying multiple coats of pearl or if shop is below 70F.
    2.    Apply 2 medium-wet coats of HC-7642 with 3-5 minutes flash between coats.
    3.    Do not apply more clear after 1 hour from completion.
    4.    HC-7642 is a water "white"(clear) clear!
    5.    Spray product as you want it to look. It does not "flow" and is meant to duplicate factory orange peel
    6.    Can be buffed after overnight dry.  After 12 hours, this product is 90-95% cured and can be buffed, striped or delivered.
    7.    Can be baked at 140 for 20 minutes and is 95% cured (to buff or deliver) in 3 hours after cool-down
Allow 2 weeks for TOTAL CURE

Flash/Dry Times (Air Dry):

Flash Between Coats: 3-5 minutes

Dust Free: 10 minutes

Time to Assemble 2 hours

Time to Polish 2 hours

Time to Stripe 2 hours

Time to Deliver 2 hours

Time to Decal 8 hours

Flash/Dry Times (Bake @ 120F):

Flash Before Bake 0 minutes

Cycle Time 10 minutes at 120F metal temperature

Dust Free At cool down

Time to Assemble At cool down

Time to Polish 30 minutes after cool down

Time to Stripe 30 minutes after cool down

Time to Deliver At cool down

Polishing:

Optimum Times: Air Dry: 2 hours @ 70F; Bake: 30 minutes after cool

Sanding: Use 1500 grit or finer or use 1500 DA or finer

Compounding: Use finishing compound. Apply a thin ribbon of material to the

area to be polished. Use a double sided wool pad or a foam

pad. Maintain air polisher or variable speed polisher at 1800-

3000 rpm. Remove excess finishing compound with a clean

soft cloth prior to applying finishing polishing.

Safety:

Before using any Harpea products be sure to read all safety warnings and MSDS. Please read all directions carefully.

For professional use only by trained painters. Not for sale or use by the general public.

Technical Data & Physical Properties:

Color Clear Sprayable Viscosity 17-19 sec. #2Z

Pot Life 1 hour Mix Ratio 4:1

Weight Solids 43% 

Volume Solids 36%

Gloss Excellent Weight per Gallon 8.00 lbs

Color Holdout Excellent 

Buff Times 2 hours @ 70F

Humidity Resistance Excellent Flash Point <25F

Solvent Resistance Excellent 

Package VOC 3.5 lbs/gal

Repairability Excellent 

RTS VOC 3.50 lbs/gal

Florida Exposure Excellent

Chip Resistance Very Good

HC-2104 European Clear

HC-2104 European Clear delivers a premium-quality, high gloss finish. HC-2104 offers superior gloss, high build, and outstanding resistance to shrinkage and dieback either air-dry or bake. This is our finest HI-SOLIDS CLEAR (also available in a medium solids version HC-2100 Euro Clear).  This is made from the finest European Resins imported to America and is equal to or even superior to ANY clear made at ANY price. Like all of our PREMIER SERIES clears, we use the maximum amounts of 2 UV absorbers!

Mix Ratio:

Component                                                  Volume

HC-104 Eurpean Clear                                           2

HH-7603/5/7 Activator                                           1

HR-1360/70/80/90 OPTIONAL 10-15%   USE  ONLY  Tamco HR Series reducers which are guaranteed moisture free!  Moisture in reducers will kill this product's shine 100% of the time!

Viscosity

19-22 seconds in #2 Zahn Cup

Pot Life

2 hours at 70F

Gun Setups:

Conventional

Siphon Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)

Gravity Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)

HVLP

Siphon Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)

Gravity Feed: 1.3 mm – 1.6 mm (0.050” – 0.063”)

Air Pressures

Conventional Panel Overall

Siphon Feed: 45-55 psi at the gun 45-55 psi at the gun

Gravity Feed: 45-55 psi at the gun 45-55 psi at the gun

HVLP 8-10 psi at the gun 8-10 psi at the gun

Application:

    1.    Allow basecoat to dry 15-30 minutes – 30 minutes if applying multiple coats of pearl or if shop is below 70F.
    2.    Apply 2 medium-wet coats of HC-2104 with 15-20 minutes flash between coats.
    3.    Do not apply more clear after 2 hours from completion.
    4.    HC--2104 is a water "white" clear!
    5.    This product "flows" and you will see it level off by itself. The slower the reducer, the greater the leveling.
    6.    Can be easily buffed if Tamco BLENDED HARDENERS are used (7600 series)
    7.    Can be baked at 140 for 30-40 minutes and is 90% cured (to buff or deliver) see below for more

Flash/Dry Times (Air Dry):

Flash Between Coats: 10 minutes

Dust Free: 60 minutes

Time to Assemble Overnight

Time to Polish Overnight

Time to Stripe Overnight

Time to Deliver Overnight

Time to Decal 48 hours

Flash/Dry Times (Bake @ 140F):

Flash Before Bake 0-5 minutes

Cycle Time 30 minutes at 140F metal temperature

Dust Free At cool down

Time to Assemble At cool down

Time to Polish 20 minutes after cool down

Time to Stripe 20 minutes after cool down

Time to Deliver At cool down

Polishing:

Optimum Times: Air Dry: Overnight @ 70F; Bake: 20 minutes after cool

Sanding: Use 1500 grit or finer or use 1500 DA or finer

Compounding: Use finishing compound. Apply a thin ribbon of material to the

area to be polished. Use a double sided wool pad or a foam

pad. Maintain air polisher or variable speed polisher at 1800-

3000 rpm. Remove excess finishing compound with a clean

soft cloth prior to applying finishing polishing.

HC-2100 2:1 GLAMOUR CLEAR COAT
NOTE: Sometimes packaged as SC-2100!

DESCRIPTION

HC-2100 2:1 Glamour Clearcoat is a two-component water white clear designed for both complete and spot/panel jobs. HC-2100 has excellent flow, leveling, and superior gloss retention. HC-2100 is a lower solids version of HC-2104 and is a perfect low cost EURO CLEAR. We do have a LOW VOC version of this product available on request. See info below

HARDENERS

Part # SH-7001-04 Quarts

Part # SH-7002-04 Quarts

Part # SH-7003-04 Quarts

Part # SH-7004-04 Quarts

RECOMMENDED BASECOATS

HC-2100 2:1 Glamour Clearcoat is compatible with all the major brand basecoats sold in the U.S. Follow the manufacturer’s recommendations for basecoat application before applying HC-2100 2:1 Glamour Clearcoat.

V.O.C. INFORMATION

HC-2100 clear V.O.C.: 496 g/l (4.20#/gal)

Less exempt solvent V.O.C.: 496 g/l (4.20#/gal)

Mixed product V.O.C.: 496 g/l (4.20#/gal)

These products may require several components and must be mixed properly to comply with V.O.C. regulations. These products are not recommended as part of a multi-coat system if the V.O.C. exceeds local, state or federal regulations.

MIXING DIRECTIONS

2 parts HC-2100 2:1 Glamour Clearcoat

SH-7001-Fast

SH-7002 Medium Hardener

SH-7003 Slow Hardener

SH-7004 Ultra Slow Hardener

APPLICATION INSTRUCTIONS

1. Follow manufacturer’s recommendations for applying their basecoat system.
2. Allow 15 minutes flash time before applying clearcoat.
3. Adjust air pressure to 45-50 psi at the gun
4. Apply 2 medium coats of SC-2100 Universal Glamour Clearcoat. Allow 5-10 minutes flash time between coats. A third coat may be applied if buffing is planned after 30-40 minutes of second coat
5. Allow vehicle to dry overnight before exposing to weather or finessing
   

Dry Times at 75°F:

• Dust free – 20 minutes  Tape free – 8 hours
• Tack Free – 4 hours  Delivery – overnight
  

COLD SHOP CONDITIONS

For maximum paint performance, vehicle should be kept above 75°F for 8 hours. Temperatures below 60°F will severely retard dry times and through cure of urethane clearcoats. Two ounces of accelerator per mixed gallon may be added to speed up cure times.

CLEANING

Clean equipment with a quality lacquer thinner, acetone, or other V.O.C. compliant solvent according to Federal, State, or Local V.O.C. regulations. Do not leave catalyzed clear in the gun more than 4 hours.

TECHNICAL DATA & PHYSICAL PROPERTIES

Color Clear
Sprayable Viscosity (RTS) 18-20 sec. EZ Zahn #2

Pot Life 4 hours Mix 
Ratio 2:1

Theoretical Dry Film 480 ft² @ 1 Mil 
Weight Solids (RTS) 40.4%

Gloss Retention Excellent 

Humidity Resistance Excellent 
Weight Per Gallon 7.90 lbs. (avg)

Solvent Resistance Excellent 
Gloss 97%

Repair ability Excellent Flash point 22F.

Florida Exposure Excellent 
Package V.O.C. 4.20 # / gal

Chip resistance Excellent 
RTS V.O.C. 4.20 # / gal

HC-4100 4:1 GLAMOUR CLEAR COAT
NOTE: Sometimes packaged as SC-421

DESCRIPTION

HC-4100 4:1 Glamour Clearcoat is a two-component water white clear designed for both complete and spot/panel jobs. HC-4100 has excellent flow, leveling, and superior gloss retention. HC-4100 is a 38% solids clear coat using a combination of European and American Resins.  The product has a Euro look, but an American type quick dry and film hardness. One of the Resins used is the same found in our HC-2100, and has similar characteristics.  We do have a LOW VOC version of this product available on request. See info below

HARDENERS

Part # HH-76 Series Hi Solids in Quarts

Part # HH-7603-04 Quarts  FAST

Part #HH-7605 -04 Quarts  STANDARD

Part # HH-7607-04 Quarts  SLOW

RECOMMENDED BASECOATS

HC-4100 4:1 Glamour Clearcoat is compatible with all the major brand basecoats sold in the U.S. Follow the manufacturer’s recommendations for basecoat application before applying HC-4100 4:1 Glamour Clearcoat.

V.O.C. INFORMATION

HC-4100 clear V.O.C.: 4.50#/gal

Mixed product V.O.C.:  4.40#/gal

These products may require several components and must be mixed properly to comply with V.O.C. regulations. These products are not recommended as part of a multi-coat system if the V.O.C. exceeds local, state or federal regulations.

MIXING DIRECTIONS

4 parts HC-4100 4:1 Glamour Clearcoat with:

1 Part

Part # HH-7603-04 Quarts  FAST

Part #HH-7605 -04 Quarts  STANDARD

Part # HH-7607-04 Quarts  SLOW

APPLICATION INSTRUCTIONS

1. Follow manufacturer’s recommendations for applying their basecoat system.
2. Allow 15 minutes flash time before applying clearcoat.
3. Adjust air pressure to 45-50 psi at the gun
4. Apply 2 medium coats of SC-2100 Universal Glamour Clearcoat. Allow 5-10 minutes flash time between coats. A third coat may be applied if buffing is planned after 30-40 minutes of second coat
5. Allow vehicle to dry overnight before exposing to weather or finessing
   

Dry Times at 75°F:

• Dust free – 20 minutes  Tape free – 6-8 hours
• Tack Free – 4 hours  Delivery – overnight
  

COLD SHOP CONDITIONS

For maximum paint performance, vehicle should be kept above 75°F for 8 hours. Temperatures below 60°F will severely retard dry times and through cure of urethane clearcoats. Two ounces of accelerator per mixed gallon may be added to speed up cure times.

CLEANING

Clean equipment with a quality lacquer thinner, acetone, or other V.O.C. compliant solvent according to Federal, State, or Local V.O.C. regulations. Do not leave catalyzed clear in the gun more than 4 hours.

TECHNICAL DATA & PHYSICAL PROPERTIES

Color Clear
Sprayable Viscosity (RTS) 15-17 sec. EZ Zahn #2

Pot Life 4 hours Mix 
Ratio 4:1

Theoretical Dry Film 480 ft² @ 1 Mil 
Weight Solids (RTS) 37.4%

Gloss Retention Excellent 

Humidity Resistance Excellent 
Weight Per Gallon 7.70 lbs. (avg)

Solvent Resistance Excellent 
Gloss 95%

Repair ability Excellent Flash point 22F.

Florida Exposure Excellent

Chip resistance Excellent 

 HC-7600 4:1 Super Fast CLEAR COAT

HC-7600 Ultra Productive Clear is a medium-solids clear that offers fast dry times both air dry and bake. This clear can be polished in as fast as 2 hours air dry and 20 minutes when baked at 120F.

Mix Ratio:

Component Volume Weight (Cum. Qty)

HC-7600 Ultra Productive Clear 4        684 grams

HH-7603/7605/7607 Activator   1        871 grams

Viscosity

15-17 seconds in #2 Zahn Cup

Pot Life

1 hours at 70F

Gun Setups:

Conventional

Siphon Feed: 1.5 mm – 1.7 mm (0.059” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.055” – 0.063”)

HVLP

Siphon Feed: 1.6 mm – 1.7 mm (0.063” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.050” – 0.063”)

Air Pressures

Conventional

Siphon Feed: 25-35 psi at the gun

Gravity Feed: 25-35 psi at the gun

HVLP 6-8 psi at the gun

Application:

1. Allow basecoat to dry 15-30 minutes – 30 minutes if applying multiple coats of pearl or if shop is below 70F.
2. Apply 2 medium-wet coats of HC-7600 with 3-5 minutes flash between coats.
3. Do not apply more clear after 1 hour from completion.

Flash/Dry Times (Air Dry):

Flash Between Coats: 3-5 minutes

Dust Free: 10 minutes

Time to Assemble 2 hours

Time to Polish 2 hours

Time to Stripe 2 hours

Time to Deliver 2 hours

Time to Decal 8 hours

Flash/Dry Times (Bake @ 120F):

Flash Before Bake 0 minutes

Cycle Time 10 minutes at 120F metal temperature

Dust Free At cool down

Time to Assemble At cool down

Time to Polish 30 minutes after cool down

Time to Stripe 30 minutes after cool down

Time to Deliver At cool down

Polishing:

Optimum Times: Air Dry: 2 hours @ 70F; Bake: 30 minutes after cool

Sanding: Use 1500 grit or finer or use 1500 DA or finer

Compounding: Use finishing compound. Apply a thin ribbon of material to the

area to be polished. Use a double sided wool pad or a foam

pad. Maintain air polisher or variable speed polisher at 1800-

3000 rpm. Remove excess finishing compound with a clean

soft cloth prior to applying finishing polishing.

Safety:

Before using any Tamco products be sure to read all safety warnings and MSDS. Please read all directions carefully.

For professional use only by trained painters. Not for sale or use by the general public.

Technical Data & Physical Properties:

Color Clear Sprayable Viscosity 15-17 sec. #2Z

Pot Life 2 hours Mix Ratio 4:1

Weight Solids 37% Volume Solids 31%

Gloss Excellent Weight per Gallon 8.00 lbs

Color Holdout Excellent Buff Times 2 hours @ 70F

Humidity Resistance Excellent Flash Point 25C

Solvent Resistance Excellent Package VOC 4.50 lbs/galRepairability Excellent RTS VOC 4.20 lbs/gal

Florida Exposure Excellent Chip Resistance Very Good

HC-1100 4:1 GLAMOUR CLEAR COAT
NOTE: Sometimes packaged as SC-2000

DESCRIPTION

HC-1100 4:1 Glamour Clearcoat is a two-component designed for both complete and spot/panel jobs. It has excellent flow, leveling, and gloss retention. HC-1100 is a 31% solids clear coat that uses our economy line 7000 series hardeners (39%).  When combined the product sprays at about 33-34% solids giving a quick dry time and film hardness.

HARDENERS

Part # HH-7000 Series Hi Solids in Quarts

Part # HH-7001-04 Quarts  FAST

Part # HH-7002 -04 Quarts  STANDARD

Part # HH-7003-04 Quarts  SLOW

RECOMMENDED BASECOATS

HC-1100 4:1 Universal Clearcoat is compatible with all the major brand basecoats sold in the U.S. Follow the manufacturer’s recommendations for basecoat application before applying HC-1100 4:1 Clearcoat.

V.O.C. INFORMATION

HC-1100 clear V.O.C.: 4.75#/gal

Mixed product V.O.C.:  4.50#/gal

These products may require several components and must be mixed properly to comply with V.O.C. regulations. These products are not recommended as part of a multi-coat system if the V.O.C. exceeds local, state or federal regulations.

MIXING DIRECTIONS

4 parts HC-1100 4:1 Universal Clearcoat with:

1 Part

Part # HH-7001-04 Quarts  FAST

Part #HH-7002 -04 Quarts  STANDARD

Part # HH-7003-04 Quarts  SLOW

APPLICATION INSTRUCTIONS

1. Follow manufacturer’s recommendations for applying their basecoat system.
2. Allow 15 minutes flash time before applying clearcoat.
3. Adjust air pressure to 45-50 psi at the gun
4. Apply 2 medium coats of SC-2100 Universal Glamour Clearcoat. Allow 5-10 minutes flash time between coats. A third coat may be applied if buffing is planned after 30-40 minutes of second coat
5. Allow vehicle to dry overnight before exposing to weather or finessing
   

Dry Times at 75°F:

• Dust free – 20 minutes  Tape free – 6-8 hours
• Tack Free – 4 hours  Delivery – overnight
  

COLD SHOP CONDITIONS

For maximum paint performance, vehicle should be kept above 75°F for 8 hours. Temperatures below 60°F will severely retard dry times and through cure of urethane clearcoats. Two ounces of accelerator per mixed gallon may be added to speed up cure times.

CLEANING

Clean equipment with a quality lacquer thinner, acetone, or other V.O.C. compliant solvent according to Federal, State, or Local V.O.C. regulations. Do not leave catalyzed clear in the gun more than 4 hours.

TECHNICAL DATA & PHYSICAL PROPERTIES

Color Clear
Sprayable Viscosity (RTS) 15-17 sec. EZ Zahn #2

Pot Life 4 hours Mix 
Ratio 4:1

Theoretical Dry Film 370 ft² @ 1 Mil 
Weight Solids (RTS) 33.4%

Gloss Retention Excellent 

Humidity Resistance Excellent 
Weight Per Gallon 7.70 lbs. (avg)

Solvent Resistance Good
Gloss 92%

Repair ability Excellent Flash point 22F.

Florida Exposure Good

Chip resistance Good

 HC-1000 4:1 Super Fast CLEAR COAT

  A lower solids version of our Super Fast HC-7600 Clear .

HC-7600 Ultra Productive Clear is a medium-solids clear that offers fast dry times both air dry and bake. This clear can be polished in as fast as 2 hours air dry and 20 minutes when baked at 120F.

Mix Ratio:

Component Volume Weight (Cum. Qty)

HC-1000 Speed  Clear                4        

HH-7001,7002,7003  Activator    1     

Viscosity

15-17 seconds in #2 Zahn Cup

Pot Life

1 hours at 70F

Gun Setups:

Conventional

Siphon Feed: 1.5 mm – 1.7 mm (0.059” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.055” – 0.063”)

HVLP

Siphon Feed: 1.6 mm – 1.7 mm (0.063” – 0.067”)

Gravity Feed: 1.4 mm – 1.6 mm (0.050” – 0.063”)

Air Pressures

Conventional

Siphon Feed: 25-35 psi at the gun

Gravity Feed: 25-35 psi at the gun

HVLP 6-8 psi at the gun

Application:

1. Allow basecoat to dry 15-30 minutes – 30 minutes if applying multiple coats of pearl or if shop is below 70F.
2. Apply 2 medium-wet coats of HC-1000 with 3-5 minutes flash between coats.
3. Do not apply more clear after 1 hour from completion.

Flash/Dry Times (Air Dry):

Flash Between Coats: 3-5 minutes

Dust Free: 10 minutes

Time to Assemble 2 hours

Time to Polish 2 hours

Time to Stripe 2 hours

Time to Deliver 2 hours

Time to Decal 8 hours

Flash/Dry Times (Bake @ 120F):

Flash Before Bake 0 minutes

Cycle Time 10 minutes at 120F metal temperature

Dust Free At cool down

Time to Assemble At cool down

Time to Polish 30 minutes after cool down

Time to Stripe 30 minutes after cool down

Time to Deliver At cool down

Polishing:

Optimum Times: Air Dry: 2 hours @ 70F; Bake: 30 minutes after cool

Sanding: Use 1500 grit or finer or use 1500 DA or finer

Compounding: Use finishing compound. Apply a thin ribbon of material to the

area to be polished. Use a double sided wool pad or a foam

pad. Maintain air polisher or variable speed polisher at 1800-

3000 rpm. Remove excess finishing compound with a clean

soft cloth prior to applying finishing polishing.