Tamco DTA (Direct to Anything) Epoxy Primer

(new picture coming soon)

DTA Premium 2K EPOXY Primer

 REVOLUTIONARY 2K EPOXY MADE IN THE USA ONLY BY TAMCO

--- No other epoxy comes close to what DTA can do!

DTA (Direct to ANYTHING) EPOXY Premium 2k DTM Primer-Sealer is a special 1:1 Epoxy Primer with exceptional chemical adhesion to almost all substrates and direct-to-metal properties. Very soft sanding, wet or dry after short dry times. DTA Epoxy Primer provides NO shrinkage and the maximum in color holdout properties available in any product. DTA may be used as a non-sanding primer-sealer.

DTA is a unique blend of special state of the art epoxy resins that has been tested to chemically adhere to almost any surface WITHOUT SANDING! Although Tamco always recommends sanding primers for ultimate adhesion and appearance, DTA 2K Epoxy has been tested over STAINLESS STEEL, ALUMINUM, GALVANIZE and other special metals without any sanding.  It has been developed for strong bonding and coating on substrates that epoxy resin shows poor adhesion. Tamco strongly recommends the use of our HR-397 cleaner before applying our DTA. A surface with any contamination will cause failure! Before using on an unknown surface, we suggest that a small test area is always coated first for adhesion qualities.

DTA 2K Epoxy was formulated with the industry’s best corrosion inhibiting ingredients to help keep rust from forming.

DTA is a proprietary resin that is only available at Tamco Paint. There is NO EPOXY sold aftermarket in the USA using this resin! It is used on an OEM basis by the largest aircraft manufacturer in America.

We can also formulate this in a wide range of HIGH GLOSS direct to anything COLORS as well as make both the primer and color DIRECT TO RUST.

Applicable Metal Substrates
- Aluminum - Magnesium
- Titanium - Bronze
- Stainless steel - Nickel
- Copper - Nickel Chrome plating
- Steel -
Ferrous and nonferrous alloy etc.

Don’t be fooled by epoxies, use the one that has been tried and used for 7 years in every type application known! ONLY MADE BY TAMCO for retail distribution in the USA.
 

Mix Ratio:

Component Volume

DTA Aerospace 2k DTA Primer                       1Part

DTA Activator                                              1Part

Allow 10 minute induction time  DO NOT REDUCE

Viscosity

24-28 seconds in #2 Zahn Cup

Pot Life

8 hours at 70F

Gun Setups:

Conventional

Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)

Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)

HVLP

Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)

Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)

Air Pressures

Conventional

Siphon Feed: 35-45 psi at the gun

Gravity Feed: 30-40 psi at the gun

HVLP 8-10 psi at the gun

Application:

1. Clean surface thoroughly using HR-397 Cleaner
2. Apply 1-2 medium coats of DTA with 20-25 minutes flash between coats.
3. Can apply Topcoat after 30 minutes flash time without sanding, or for extra quality finish wet sand primer with 280-320 grit sandpaper before applying topcoats.

(Air Dry):

Flash Between Coats: 20-25 minutes

Wet Sanding: 8-12 hours

Wet on Wet 30 minutes to 1 hour. Maximum time for applying top-coat over non-sanded primer is 2 weeks.

Safety:

Before using any Tamco products be sure to read all safety warnings and MSDS. Please read all directions carefully.

For professional use only by trained painters. Not for sale or use by the general public.

SPECIAL NOTES

DTA is a unique blend of special state of the art epoxy resins that has been tested to chemically adhere to almost any surface WITHOUT SANDING! Although Tamco always recommends sanding primers for ultimate adhesion and appearance, DTA 2K Epoxy has been tested over STAINLESS STEEL, ALUMINUM, GALVANIZE and other special metals without any sanding. Tamco strongly recommends the use of our HR-397 cleaner before applying our DTA. A surface with any contamination will cause failure! Before using on an unkown surface, we suggest that a small test area is always coated first for adhesion qualities.

DTA 2K Epoxy was formulated with the industry’s best corrosion inhibiting ingredients to help keep rust from forming.

COLORS AVAILABLE:

WHITE, GRAY, BLACK OR CLEARBASE*

Clear-base Epoxy must be colored with Tamco Colorants ONLY and can made in over 600 different colors!