Tamco Cleaners and Solvents

Tamco's HR- Reducers, the best reducers money can buy  

Tamco's Reducers are AFFORDABLE, but quality is NOT LOST.  We use ONLY “urethane grade solvents.” in all our products. Only big time companies do this - most generics DO NOT. Here is the recommendation from Rhodia Tolonate on water:Water content of the solvent(s) and impurities  reacting with NCO.... Like all isocyanates, Tolonate reacts with water. It is therefore essential to use solvents with a water content lower than 500 ppm (preferably lower than 300 ppm), which are referred to as ”urethane grade solvents.”  purities likely to react with NCO groups, such as butanol and/or acetic acid in butyl acetate. (Our solvents we buy are under 150 ppm!  That’s adds 25% to our cost! Even our reducers use these high grade solvents!)  

 

HR-1360 Fast is a cold climate solvent only, mainly for basecoats where catalysts are not used. It can be used in our 2K Primers, and Colors however, as they are all certified urethane grade solvents.  Also great for cleanup- because 50% of the ingrediants is acetone. Low VOC, and super cleaning abilities.

HR-1370- Standard Medium Reducer. Use from 75-95 degrees depending on surface size to keep wet.

HR-1380- Slow Reducer. Use only above 85 degrees, up to 95 degrees.

HR- 1390- is xtra slow reducer, for temperatures over 95%! However 2K paints are not recommended to be sprayed over 95 degrees!

HR-900 RETARDER!

Safety:

Before using any Tamco products be sure to read all safety warnings and MSDS. Please read all directions carefully.

For professional use only by trained painters. Not for sale or use by the general public.

TAMCO HR-397 Pre Cleaner
The Best Wax and Grease remover you will ever use!

CLEANS better than anyone's Prep Solvent

DO NOT USE ON FRESH PAINT!

The best most aggressive wax and grease remover on the market use BEFORE you start painting. Not safe for fresh paints.

Use Tamco's Final Wipe (HR-398) for fresh paint cleaner

Steps:

1) Wash area to be painted with soap and water and wipe dry

2) Apply HR-397 on a clean cloth (or use a pump sprayer) and apply very wet on surface.

3) BEFORE solvent dries, wipe the area again with a clean dry lint free cloth, trying to move in one direction. Do not allow to dry!

4) Apply again to areas that dried, or start sanding and priming as per instructions

  HR-398 Final Wipe

The Best Anti-Static Final Wipe Wax and Grease remover you will ever use!

Tamco's HR-398 is the only anti-static final wipe that will actually cut down on dirt in paint you can buy. We use a proprietary unique formula that uses an anti-static solvent which will eliminate the need for alcohol PREP WIPES. Safe for all finishes, and most carpets!

Works Great. 

1) Wipe on with clean rag (or solvent sprayer) and wipe off before drying.

2) after surface is clean and dry surface is ready to be painted.

Reduces dirt, removes hand prints -- use in booth prior to spraying and tacking

FOR MAXIMUM WAX and GREASE REMOVAL on OLD FINISHES (before sanding) USE OUR HR-397 Degreaser 

HR-397W Water PreCleaner and DeWaxer

The Best Waterbase Wax and Grease remover you will ever use!

CLEANS better than anyone's Solvent based Prep Solvent

Legal Everywhere!  ZERO VOC - Non-Flammable, will not burn!

DO NOT USE ON FRESH PAINT!

NON TOXIC- NON HAZARDOUS - NOT FLAMMABLE or COMBUSTIBLE!

The best most aggressive water-based wax and grease remover on the market

use BEFORE you start painting. Not safe for fresh paints. 

1) Wash area to be painted with soap and water

2) Apply HR-397W on a clean cloth or use a pump sprayer

3) Allow to falsh dry (this product will not look like water, but dry like a solvent-based cleaner!

4) Primer and paint as directed

For a fresh paint Final wipe mixture , Mix 1 part 397W with 4 Parts distilled water and product is safe as a final wipe!