Tamco

Tamco

Thursday, September 18, 2014

Duraflint I Clear or Color Tech Info

HC-9040 Polyurethane

9040 Series Duraflint 1
POLYURETHANE ENAMEL SYSTEM 3:1:(1)
FEATURES:
> Easy to apply metallic colors
> Outstanding gloss
> Superior flow-out and leveling
> Outstanding durability
> Excellent gloss & color retention
> Economical to use

MIX RATIO:
--3 parts Polyurethane color
--1 part HH-50 Standard High Solids hardener (or HH7603 Fast, HH-7605- Medium, HH-7607 Slow)
--up to-1 part HH-Reducer (Metallic colors especially)

SURFACE PREPARATION:
Bare Metal:
> Wash surface of vehicle with soap and water to remove tree sap and road dirt
> Wipe vehicle with wax & grease remover.
> Sand area as necessary to remove any rust or corrosion
> Prime repaired areas with HH-5310 or 5311 2K urethane primer
> Block primed body work with 400 grit or finer wet or dry sandpaper
> Cleanse area to be painted with wax & grease remover
> Seal vehicle using HP-6001 universal sealer
Pre-painted Surfaces:
> Wash area to be painted with mild detergent and water
> Cleanse surface with wax & grease remover
> Sand area as needed to remove old paint or any rust using 320 grit D.A.
> Apply one full wet coat of HP-6001 universal sealer.
> Allow Sealer 30 minutes dry time before topcoat.

V.O.C. INFORMATION:
Urethane color V.O.C.: <569 gal="" gll="" p="">
.- Less exempt solvent V.O.C.: <569 gal="" gll="" p="">
Mixed product V.O.C.: <599 g="" gal="" p="">
This product may require several components and must be mixed properly to comply with
V. O. C. regulations. This product is not recommended as part of a multi-coat system if the
  1. O. C. exceeds local, state or Federal regulations.


POLYURETHANE SYSTEM APPLICATION DIRECTIONS:
> Adjust HVLP air pressure to 30 psi at the gun
> Apply 2 Full wet coats of Polyurethane Enamel color
> Allow 10-15 minutes flash time between color coats
> Allow vehicle to dry overnight before exposing to weather or finessing


APPLICATION INSTRUCTIONS: Intregrating clear (USE ONLY HC-9040 Clear!)
> Apply two wets coats polyurethane color per directions
> Add 1 part catalyzed color 1 part catalyzed HC-9040 clear & mix.
> Allow 20 minutes flash time before topcoat
> Apply 1 wet coat blended color / clear
> Allow overnight dry
DryTimes @ 75F
> Dust free – 20-30 minutes
> Tack free - 3-4 hours
> Tape free – 12 hrs.
> Delivery - overnight

For maximum paint performance, vehicle should be kept above 75°F. Temperatures
below 60°F will severely retard dry times and thorough cure of urethanes.
1 ounce of TAMCURE Accelerator per mixed gallon may be added to speed up
cure.

CLEANING
Clean equipment with a quality lacquer thinner.
Do not leave catalyzed paint in the gun more than 4 hours.

TECHNICAL DATA:
PRODUCT SAFETY INFORMATION:
Consult Material Safety Data Sheet
Color Clear Sprayable Viscosity 18-20 sec. #2Z
Pot Life 4-8 hour Mix Ratio 3:1
Weight Solids 38% Volume Solids 35%
Gloss Excellent Weight per Gallon 8.10 lbs
Color Holdout Excellent 
Humidity Resistance Excellent Flash Point <25 span="">F
Solvent Resistance Excellent Package
VOC 3.25 lbs/galRepairability 
Excellent RTS VOC 3.50 lbs/gal
Florida Exposure Excellent 
Chip Resistance Excellent


a BFE company